CombiLoader

CombiLoader

CombiLoader $193

CombiLoader

CombiLoader

Popular Bestseller Points: 2

In stock Product code: combiloader

SMS-Soft Brand

$193

Price in reward points: 193

Shipping Information

Enter a delivery address

Country

Region / State

Post Code

City

Description

Loader v.3 - a program for reading and writing firmware in engine control units of domestic and imported cars. Allows firmware without removing the ECU from the car, using the OBD2 connector, for those types of ECUs where it is possible. The loader is convenient to use, reliable, has many additional functions, is updated and supported by technical support.

Manufacturer: Russian company "AVTOELECTRIC".

The basic kit includes a USB protection key, and subsequently purchased modules are tied to the key.

In case of key loss, modules CANNOT be restored.

Attention! The Combiloader is not sold without a module! You must add at least one module to your order. Orders without module will be cancelled. The money transfer fee may be lost.

Program capabilities:

ability to create dual-mode firmware for Janvar-5.1, Janvar-7.2, VS-5.1, and Mikas-7.1
removal of additional error masks in the latest versions of factory software
protection against reading by self-destruction of firmware when attempting to read
embedding starter lock functions in the program code
embedding a route computer with 20 functions in the program code
protection against copying by setting the number of illegal starts
simultaneous work with a pair of FLASH / EEPROM
correction of all firmware identifiers
reading the immobiliser status and disabling it
correction of passport data stored in EEPROM
removal of additional checksum verification
correction of checksums
Error correction in serial software

Basic Set Modules:

BSL mode C16x: a wide range of imported and domestic vehicles equipped with ECU based on C16x microcontrollers.
BSL mode ST10F168: any types of ECUs with ST10F168 family processors, such as MagnetiMarelli IAW 59F installed in Fiat cars.
BSL mode ST10F27x: a wide range of imported and domestic vehicles equipped with ECU based on ST10F27x microcontrollers.
BSL mode ST10F280: any types of ECUs with ST10F280 family processors, such as MagnetiMarelli 6LPB installed in Peugeot cars.
BSL mode ST10F296: any types of ECUs with ST10F296 family processors, such as MagnetiMarelli 4HV installed in Skoda Octavia/Fabia with 1.4L engine (BUD).
January-5.1: VAZ vehicles.
January-7.2: VAZ vehicles.
VS-5.1: VAZ vehicles.
Bosch C509 Hyundai/Kia: Hyundai/Kia vehicles with ECU based on C509 processors with external Am29F010 FLASH.
Bosch MP7.0: VAZ vehicles.
Bosch M7.9.7(+): VAZ vehicles, Bosch M7.9.7 ECU.
Mikas-7.1: GAZ and UAZ vehicles.
Mikas-7.6: ZAZ and Daewoo vehicles.

All other modules are purchased separately. To purchase modules, you need to provide the host number and key serial number. You can find both numbers in the program itself through the menu ("Help" - "About the program").

Some modules require a J2534 adapter, such as Dialink, OpenPort 2.0, Scanmatic 2 PRO.

Basic Configuration:

Software Package LOADER V3 (COMBILOADER)
USB Host
Adapter
USB Key

The extended set includes two cables: 55 pin and 81 pin.

The 55 pin cable is used for working with January-5, Mikas-7 blocks. Suitable for January-5.1, VS-5.1, MIKAS-7.6, MIKAS-7.1, and others.
The 81 pin cable is used for working with Bosch M7.9.7, January-7.2, Mikas-11, M73, MIKAS-10.3, and others.

Modules

Recommended Articles

Installation and activation Combiloader

Installation and activation Combiloader 13 September, 2024

Tags: combiloader

Please select required options

In Stock
Combiloader M11/73A [000] module

$113

The Combiloader M11/73A module is designed to work with vehicles equipped with closed ECU Mikas-11 (ET, CR) and M73 with the latest software versions. The module allows you to work with closed ECUs that cannot be accessed using standard modules such as Mikas-11/Mikas-11ET/Mikas-11CR/VS-8, January-7.2+/M73, or BSL. The MIKAS-11 control units are used in cars such as Volga, Gazelle, Sobol, UAZ, GAZ, and PAZ buses. The module is used to read the ECU in order to create a backup of its contents and to restore the ECU's contents from the backup or to restore (update an outdated version of) the original ECU software in case there are suspicions of non-original (modified) control software installed, the use of which is not certified by the ECU manufacturer. To use the module, you need to purchase the Loader Package v.3. The loader package can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you will need the serial number of the key, USB host, full name, and email address. Activation is done during business hours within 5-10 minutes and may be delayed for 1-2 hours on weekends.
In Stock
Combiloader Mikas 10.3 (M114) [001] module

$44

Module Combiloader Mikas 10.3 (M114) is designed for flashing software, reading/writing calibrations, and EEPROM contents of Mikas-10.3 (M114) controllers. The module allows for chip-tuning of ECU Mikas-10.3 M114 - a new version of ECU M10.3 that is installed in Daewoo Sens, Gazelle, and other vehicles. To use the module, you need to purchase a Loader Pack v.3 The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you need the serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Delphi MT20U [002] module

$88

Module Combiloader Delphi MT20U is designed for reading and writing FLASH and EEPROM of Delphi MT20U ECUs installed in Chinese cars. The module allows for ECU chip tuning of Delphi MT-20U installed in Chinese-made cars (Great Wall, BYD, and others). Supported ECUs: MT-20U MT20U2 MT20UED MT22U MT22.1 MT22.1.1 MT22.5 ATTENTION! Delphi MT22.5 ECUs have two different hardware modifications (externally identical): Programmable via K-Line: this module supports working with such ECUs Programmable via CAN: this module does not support working with such ECUs, you need to use module MT22.x Module functions: Read and write full FLASH Read and write EEPROM Read and write calibrations The module works through the car's OBD2 connector or on the bench when directly connected to the control unit. To work, you need an OBD2 cable, which is not included in the standard kit. To connect the ECU on the bench, you need a Combibox or a universal socket. To use the module, you need to purchase a Combiloader Package v.3 The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need the serial number of the key, USB host, full name, and email address. Activation is carried out during business hours within 5-10 minutes, with a delay of 1-2 hours on weekends.
In Stock
Combiloader Siemens SIMK3x/4x [003] module

$76

Module Combiloader Siemens SIMK3x/4x is designed for reading/writing the entire firmware or calibration area by diagnostic method, without removing the ECU from the car. The module supports cars of Korean, Chinese, and Iranian production, equipped with ECU Siemens SIMK31, SIMK41, SIMK43, SIM2K-33, SIM2K-34VR, the work is carried out through the diagnostic connector (K-Line interface). The following types of ECUs are supported: SIMK31: Chery QQ 0.8L SIMK41: Tiburon 2.0, Elantra 2.0, Tuscani 2.0 SIMK43: Kia, Hyundai (various models) SIM2K-34VR: Iran Khodro Samand To work with the module, you need to purchase Loader Package v.3 The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is carried out during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader Bosch M(G)7.9.8 HK [004] module

$88

Combiloader Module Bosch M(G)7.9.8 HK is designed for flashing the FLASH memory of the ECU Bosch M7.9.8/MG7.9.8 through the diagnostic connector on KIA/Hyundai vehicles. The module supports operation on Kia/Hyundai vehicles with ECU Bosch M7.9.8 (MG7.9.8) installed on these vehicles since 2006, through the OBD2 connector, without removing the control unit from the vehicle. J2534 adapter is required for operation. The module requires the purchase of Loader Kit v.3 which can be purchased in our store. One loader can be used for an unlimited number of modules. To activate the module, you need the following: serial number of the key, USB host, full name and email address. Activation is carried out during working hours within 5-10 minutes, with a delay of 1-2 hours on weekends.
In Stock
Combiloader Siemens SIMK3x/4x J2534 [005] module

$63

Combiloader Module Siemens SIMK3x/4x J2534 is designed for reading/writing the entire firmware or calibration area by diagnostic method without removing the ECU from the car. The module supports Korean, Chinese, and Iranian cars equipped with Siemens SIMK31, SIMK41, SIMK43, SIM2K-33, SIM2K-34VR ECUs, and the work is done through the diagnostic connector (K-Line and CAN interface). Software versions that use CAN or K-Line bus for reading and writing firmware are supported. J2534 interface is required for operation. The following types of ECUs are supported: SIMK31: Chery QQ 0.8L SIMK41: Tiburon 2.0, Elantra 2.0, Tuscani 2.0 SIMK43: Kia, Hyundai (various models) SIM2K-34VR: Iran Khodro Samand To use the module, you need to purchase Loader Package v.3 The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Bosch M(E)7.x [006] module

$63

Diagnostic Module for Flashing ECUs Without Removal Module enables direct flashing of ECUs via the vehicle’s diagnostic port, eliminating the need for ECU removal. For LADA vehicles, connection is made directly to the ECU connector, avoiding the need to disassemble the unit. Supported ECU Models The module is fully compatible with several Bosch ECU models, including: MSE3.0 M7.9.7 ME7.9.7 M7.9.71 (M7.9.7+) M7.8 ME7.8.8 To work with the module, it is necessary to purchase a Loader Package v.3 The loader package can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you need: the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Bosch ME9.x/Bosch ME7.9.9 [008] module set

$51

Module Combiloader Bosch ME9.x/Bosch ME7.9.9 is designed for reading/writing FLASH memory of the engine control unit (ECU) Bosch ME9.6/E55 and Bosch ME9.6.2/E69, Bosch ME9.1/E77, installed in Chevrolet/Opel/Caddilac/SAAB vehicles through the diagnostic connector. Bosch ME9.x GM module performs automatic recalculation of checksums of the written calibrations. J2534 interface is required for operation. To use the module, the purchase of a Loader Package v.3 is required. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you will need: the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Delphi MT80, MT60, Simtec76 [009] module set

$63

The Combiloader Delphi MT80, MT60, Simtec76 module kit is designed for reading and writing the FLASH memory of Delphi ECUs installed in GM vehicles via the diagnostic connector. To work with MT60/MT80 ECUs, which provide full access to FLASH/EEPROM without the need for disassembly, you can expand the module's capabilities by purchasing an additional license, available as the MT60/MT80. The modules automatically recalculate checksums for the written calibrations when the program's full firmware is available in the buffer. Compatibility: Delphi MT60: Daewoo Gentra Delphi MT80: Chevrolet Aveo and Chevrolet Cruze Siemens SIMTEC76: Chevrolet Cruze, Chevrolet Orlando, Daewoo Lacetti Standard reading/writing time for MT60/MT80: 21/4 min. With the use of the extension: 1/1.5 min. An adapter J2534 is required for operation. To use the module, you need to purchase the Programming Package v.3 You can purchase the programming package in our store, and one package allows you to buy an unlimited number of modules. To activate the module, you will need the serial number of your key, USB host, your full name, and email address. Activation is carried out during working hours and usually takes 5-10 minutes, with possible delays of 1-2 hours on weekends.
In Stock
Combiloader Vagon VAx [010] module

$51

Module Combiloader Vagon VAx is designed for reading and writing FLASH and EEPROM of Vagon VAx ECUs installed in Lifan Breeze and other cars. The module allows for chip tuning of Vagon VAx ECUs installed in Chinese-made cars such as Lifan Breeze 1.3L/1.6L and others. The module allows you to: Read/write the entire FLASH image Read/write the calibration area Read/write the EEPROM To use the module, you need to purchase the Loader Package v.3 The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need the serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader M74 K-Line (VAZ) [011] module

$32

Module Combiloader M74 (VAZ) K-Line is designed for reading and writing FLASH/EEPROM of ECU M74, produced on Infineon XC27x5 processors through the built-in BootStrapLoader. The module allows to work with "Lada Grant" cars with electronic gas pedal, equipped with ECU M74 (K-Line). Programming of the ECU is done through the control unit connector without disassembling the ECU. Both ECUs with an external EEPROM chip and ECUs that use the processor's FLASH for EEPROM emulation are supported. For convenience of connecting to ECU M74, you can purchase M74 cable. To use the module, you need to purchase Loader Kit v.3. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you need: serial number of the key, USB host, full name and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader HK Siemens SIM2K/MT38/MT86 [012] module set

$88

Combiloader HK Siemens SIM2K/MT38/MT86 module set is designed for reading/writing Siemens SIM2K/MT38/MT86 ECUs installed on Hyundai/Kia vehicles without removing the control unit from the vehicle. Supported ECUs and vehicles: Siemens SIM2K C201/240/241/242/245 ECU is installed on Hyundai, Kia, SsangYong vehicles. The module allows reading/writing FLASH memory using diagnostic method without removing the ECU from the vehicle, it works through J2534 interface. Siemens SIM2K 140/141/141.1/142/143/341/D160 ECU is installed on Kia (Magentis, Cerato, Carens, Sorento, Sportage), Hyundai (Sonata, IX35) vehicles with engines of 2.0L and above, as well as Chevrolet Epica. The module allows reading/writing program or calibration areas using diagnostic method without removing the ECU from the vehicle. The set includes two versions of the module: Module that works through the loader adapter, using K-line for communication with the ECU Module that works through J2534 interface, using K-line or CAN bus for communication with the ECU Delphi MT38 ECU is used on Kia (Carnival, Mohave, Opirus, Magentis, Sorento), Hyundai (Genesis, Grandeur, Santa Fe, Sonata, IX55) vehicles with V6 2.7/3.3/3.8L engines. The module allows reading (only K-Line ECUs) and writing flash memory using diagnostic method without removing the ECU from the vehicle. To read the firmware from CAN ECUs, use BSL TC17xx J2534 module. The set includes two versions of the module: Module that works through the loader adapter, using K-line for communication with the ECU Module that works through J2534 interface, using K-line or CAN bus for communication with the ECU Delphi MT86 ECU is installed on Kia (Cadenza, Quoris), Hyundai (Genesis, Equus) vehicles with V6 3.3/3.8/5.0L engines. The module allows reading calibrations and writing program/calibrations using diagnostic method without removing the ECU from the vehicle. To read the full firmware from the ECU, use BSL TC17xx J2534 module, it works through J2534 interface. To use the module, you need to purchase Loader Package v.3 You can buy the loader in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader Siemens VDO MSE3.5 [014] module

$63

Module Combiloader Siemens VDO MSE3.5 is designed for reading/writing calibrations and programming ECU Siemens VDO MSE 3.5 installed in TagAz RoadPartner/TaGeR/SsangYoung Rexton vehicles. The module allows working with TagAz RoadPartner/TaGeR/SsangYoung Rexton vehicles with 2.3/2.8/3.2L engines through the diagnostic connector. To use the module, you need to purchase Loader Pack v.3 The loader can be purchased in our store. You can buy an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Renault Sirius 3x [015] module

$63

Module Combiloader Renault Sirius 3x is designed for reading/writing calibrations and programming of Siemens SIRIUS32, SIRIUS34, EMS3132, EMS3134 ECU for Lada Largus, Renault: Logan, Clio, Megane, Scenic with 1.4/1.6/2.0-liter engines. The module supports ECU programming directly on the vehicle through the diagnostic connector. To use the module, you need to purchase Loader Kit v.3 You can buy the loader kit in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, and on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader GM Simtec70/7x, Bosch M7.9.7.1, Bosch ME7.6.x, MT35E, PSG16 [016] module set

$114

Combiloader GM Simtec70/7x, Bosch M7.9.7.1, Bosch ME7.6.x, MT35E, PSG16 module set is designed for reading and writing FLASH memory of Siemens, Bosch, Delphi ECUs installed on Opel cars through the diagnostic connector. The SIMTEC70 module is designed for reading and writing FLASH memory of Siemens SIMTEC70 ECUs installed on Opel cars through the diagnostic connector. ECU compatibility table for SIMTEC 70: Opel Astra G (1998-2000) X18XE1/X20XEV Opel Vectra B (1998-2001) X18XE1/X20XEV Opel Zafira (1999-2000) X18XE1 The SIMTEC7x module is designed for reading and writing FLASH memory of Siemens SIMTEC71.x, SIMTEC75.x, and SIMTEC81 ECUs installed on Opel cars through the diagnostic connector. Two versions are included: Module that works through the Loader adapter, using the K-line for communication with the ECU Module that works through the J2534 interface, using the K-line or CAN bus for communication with the ECU ECU compatibility table for SIMTEC 71.0/71.1 (K-Line): Opel Astra G (2001-2008) Z18XE Opel Corsa C (2001-2009) Z18XE Opel Meriva (2003-2009) Z18XE Opel Tigra B (2005-2009) Z18XE Opel Vectra B (2001) Z18XE Opel Zafira (2001-2005) Z18XE Opel Omega B (2002-2003) Z22XE ECU compatibility table for SIMTEC 71.5/71.6 (CAN): Opel Astra H (2004-2007) Z18XE Opel Vectra C (2002-2007) Z18XE Opel Signum (2002-2007) Z18XE ECU compatibility table for SIMTEC 75.1/75.5 (CAN): Opel Astra H (2006-2009) Z16XER/Z18XER Opel Vectra C (2005-2009) Z18XER Opel Signum (2005-2009) Z18XER Opel Zafira B (2005-2009) Z16XER/Z18XER ECU compatibility table for SIMTEC 81 (CAN): Opel Astra H (2007-2009) Z22YH Opel Vectra C (2003-2008) Z22YH Opel Signum (2003-2008) Z22YH Opel Zafira B (2005-2009) Z22YH The Bosch ME7.6.x module is designed for reading and writing FLASH memory of Bosch ME7.6.x ECUs installed on Opel cars through the diagnostic connector. ECU compatibility table for Bosch ME7.6.x: Opel Agila (2004-2007) Z10XEP Opel Astra-G (2004-2008) Z14XEP Opel Astra-H (2004-2009) Z12XEP/Z14XEP/Z14XEL/Z20LER/Z20LEL/Z20LEH/Z16LET Opel Corsa-C (2005-2009) Z10XEP/Z14XEP Opel Corsa-D (2007-2009) Z10XEP/Z12XEP/Z14XEP/Z16LER Opel Meriva (2004-2009) Z14XEP/Z16LET Opel Tigra-B (2005-2009) Z14XEP Opel Zafira-B (2005-2009) Z20LER/Z20LEH/Z20LEL The Bosch M7.9.7.1 module is designed for flashing the FLASH memory of the Bosch M7.9.7.1 ECU installed in Chevrolet vehicles via the diagnostic connector. ECU compatibility table for Bosch M7.9.7.1: Chevrolet Aveo 1.6L The Bosch PSG16 module is designed for flashing the FLASH memory and reading/writing calibrations of the Bosch PSG16 ECU installed in GM vehicles via the diagnostic connector. The Delphi MT35E module is designed for reading/writing the FLASH memory of the Delphi MT35E ECU installed in Opel vehicles via the diagnostic connector. ECU compatibility table for Delphi MT35E: Opel Meriva (2006-2009) Z16XEP (K-Line) Opel Astra H (2004-2009) Z16XEP (CAN) Opel Astra H (2007-2009) Z16XE1 (CAN) Opel Zafira B (2005-2009) Z16XEP (CAN) Opel Zafira B (2007-2009) Z16XE1 (CAN) Opel Vectra C (2006-2009) Z16XEP (CAN) Opel Signum (2006-2009) Z16XEP (CAN) To use the module, you need to purchase the CombiLoader v.3. The CombiLoader can be purchased from our store. You can purchase an unlimited number of modules for one CombiLoader. To activate the module, you will need: the serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of 1-2 hours on weekends.
In Stock
Combiloader M74 CAN (VAZ) [019] module

$32

Module Combiloader M74 (VAZ) CAN is designed for reading and writing FLASH/EEPROM of M74 ECUs produced on Infineon XC27x5 processors via the built-in BootStrapLoader. The module allows working with Lada Grant cars equipped with electronic throttle and M74 ECU (CAN). ECU programming is done through the control unit connector without disassembling the ECU. It supports both ECUs with an external EEPROM chip and ECUs where the FLASH processor is used to emulate the EEPROM. For ease of connection to the M74 ECU, you can purchase the M74 cable. To use the module, you need to purchase the Loader Package v.3. The Loader Package can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: the key's serial number, USB host, full name, and email address. Activation is carried out during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader Delphi MR140/HV240 [020] module

$158

The Combiloader Delphi MR140/HV240 module is designed for reading/writing MR140/HV240 ECUs installed on Chevrolet, Daewoo cars through the diagnostic connector. The module allows you to restore the ECU after unsuccessful writing attempts! To use the module, you need to purchase Loader Package v.3. The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you will need the serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Ford Visteon [022] module set

$101

Combiloader Module Set for Ford Visteon is designed for reading/writing FLASH memory of Visteon ESU-131/312/411/412/415/418 ECUs installed in Ford Focus 2, C-Max, Kuga with 1.8...2.0L engines (2004...2010) and Ford Mondeo 4, S-Max, Galaxy with 2.0...2.3L engines (2004..2011). Ford Visteon module features: Requires J2534 adapter for operation Ability to open and save firmware in SMS-Soft Container File format (new format for ChipTuningPRO and CombiLoader) Ability to open and save firmware in BIN format (regular binary file) Automatic checksum calculation when saving firmware To use the module, it is necessary to purchase Loader Kit v.3. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of 1-2 hours on weekends.
In Stock
Combiloader GM Delphi ACDelco [023] module

$114

The Combiloader GM Delphi ACDelco module is designed for reading and writing FLASH memory in Delphi ACDelco E37/E38/E39/E39A/E67/E78/E80/E83/E92 ECUs installed in GM vehicles via the diagnostic connector. Compatibility Table: ACDelco E37 (2.4L — LE5/LE9) Chevrolet Captiva (C140) 2011+ Opel Antara 2011+ ACDelco E38 (4.8L — LY2; 5.3L — LY5/LC9/L45; 6.0L — LQ4/L92/L76; 6.2L — L92/L94/L9H) Chevrolet Avalanche Chevrolet Suburban Chevrolet Tahoe Cadillac Escalade GMC Yukon Hummer H2 ACDelco E39/E39A Cadillac SRX 2010+ 3.0L (LF1) Opel Insignia 2.0L A20NHT (LHU) Chevrolet Captiva (C140) 2011+ 3.0L (LF1, LFW) Chevrolet Malibu 2012+ 3.0L (LFW) Opel Antara 2011+ 3.0L (LF1) Opel Antara 2012+ 3.0L (LF1, LFW) Opel Astra‑J A16XHT/1.6L SIDI Opel Astra‑J OPC A20NHH Saab 9 — 5 A20NHT ACDelco E67 Cadillac SRX 4.6L (LH2) Hummer H3 ACDelco E78 Opel Adam A12XEL Opel Astra‑J A14NET(LUJ) Opel Corsa‑D 2012 A12XEL(LDW)/A12XER(LDC)/A14XEL(L2Z)/A14XER(LDD) Opel Mokka A14NEL/A14NET/A18XER ACDelco E80 Chevrolet Colorado Z71 Chevrolet Malibu LCV ACDelco E83 Buick Excelle GT A16LET Chevrolet Aveo‑B 2012 Z16XER(LDE)/A12XER Chevrolet Cruze‑A A16XER/A16LER Opel Adam A14XEL Opel Insignia A16XER(LDE)/A18XER(2H0) Opel Astra‑J A14XEL/A14XER(LDD)/A16XER(LDE)/A16LET(LLU)/A18XER Opel Corsa‑D 2010 A10XEP(LDB)/A12XEL(LDW)/A12XER(LDC)/A14XEL(L2Z)/A14XER(LDD) Opel Meriva‑B A14XER(LDD)/A14NET(LUJ)//A14NEL Opel Mokka A18XER ACDelco E92 Cadillac ATS 3.6L Cadillac Escalade 6.2L To use the module, you need to purchase Programming Package v.3. The programming package is available for purchase in our store, and you can use it to activate an unlimited number of modules. To activate the module, you will need the serial number of the key, USB host, your full name, and email address. Activation is carried out during working hours and usually takes 5-10 minutes, with possible delays of 1-2 hours on weekends.
In Stock
Combiloader M12.3 (M124) [025] module

$51

Combiloader Module M12.3 (M124) is designed to write the base software and read/write calibrations of the Mikas-12.3 M124/M12N engine control units installed in GAZ vehicles. The module allows you to: Read/write the calibration area Read/write the control program Calculate and automatically adjust the checksum of the calibration area, if necessary To use the module, you need to purchase the Loader Pack v.3. You can buy the loader pack in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you will need the serial number of the key, USB host, full name, and email address. Activation takes place during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader M12/M74.5/M75/М86i [026] module

$101

Module Combiloader M12/M74.5/M75/M86i is designed for reading and writing FLASH and EEPROM of ECU MIKAS 12 (12.48), M74.5, M75, and M86i, which are operated by programs produced by ELKAR/ITELMA and installed on new cars of VAZ, GAZ, and UAZ with electronic gas pedal. The functionality of module DOES NOT INTERSECT with module M86 (VAZ). Both modules are required to work with the entire M86 line. Features of module M12/M74.5/M75/M86i: Possibility to open firmware in SMS-Soft Container File format (new format for ChipTuningPRO and CombiLoader) Possibility to open firmware in BIN format (ordinary binary file) Saving firmware only in SMS-Soft Container File format, compatible with ChipTuningPRO Reading identification ECU initialization To work with the module, it is necessary to purchase Loader Package v.3. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader Ford Siemens SIM28/29/21/22/210 [027] module set

$63

Combiloader Module Set for Ford Siemens SIM28/29/21/22/210. Module Features: Requires J2534 adapter (sold separately) Ability to open and save firmware in SMS-Soft Container File format (new format for ChipTuningPRO and CombiLoader) Ability to open and save firmware in BIN format (ordinary binary file) Automatic calculation of VID block checksum when saving firmware To use the module, you need to purchase Pack Loader v.3 You can buy the loader in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation takes place during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Ford SID206/208/209/211 [028] module set

$126

Combiloader Module Set for Ford SID206/208/209/211 Module Features: SID206 is designed for reading/writing calibration and programming of Siemens SID206 ECUs installed in Ford Mondeo 4, Galaxy, S-Max, Kuga 1 vehicles with 1.8-2.0 L engines SID208 is designed for reading/writing calibration and programming of Siemens SID208 ECUs installed in Ford Transit 2.2L Diesel vehicles SID209 is designed for reading/writing calibration and programming of Siemens SID209 ECUs installed in Ford Ranger 3.2L Diesel vehicles SID211 is designed for reading/writing calibration and programming of Siemens SID211 ECUs installed in Ford Transit 2.2L Diesel vehicles Important notes for SID208/SID209/SID211 modules: During the writing process, the access password to the processor is read from the ECU, which can be used for subsequent work with the ECU using the BSL TC17xx J2534 module If the ECU performs digital signature verification (RSA enabled), it is not possible to write modified software to such a block. To disable the digital signature verification, use the BSL TC17xx J2534 module To work with SID208/SID209(CK4A) ECUs, which include full access to FLASH/EEPROM through the diagnostic connector, an extension of the module capabilities is available for purchase as an additional license. J2534 adapter is required for operation. To use the module, the purchase of Loader Package v.3 is required. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you will need: the serial number of the key, USB host, full name, and email address. Activation is done during working hours, usually within 5-10 minutes. On weekends, there may be a delay of up to 1-2 hours.
In Stock
Combiloader Delphi DCM3.7 [030] module set

$126

The Combiloader Delphi DCM3.7 module set is designed for reading/writing the FLASH memory of Delphi DCM3.7 ECUs installed in SsangYong, GM, GreatWall, Hyundai/Kia, VAG group vehicles, through the diagnostic connector. Additional features: Checksum calculation for calibration area ECU identification: allows requesting ECU identification data Error reading: reads the number of DTC codes from the ECU and displays them Error reset: resets the accumulated error information in the ECU (DTC), then performs a re-reading To work with the module, the purchase of Bootloader Kit v.3 is required. The bootloader can be purchased in our store. An unlimited number of modules can be purchased for one bootloader. To activate the module, you need the serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of 1-2 hours on weekends.
In Stock
Combiloader Renault Valeo V4X and Sagem S3K [031] module set

$63

The Combiloader module set Renault Valeo V4X and Sagem S3K is designed for reading/writing software and calibrations (boot sector and eeprom are not affected) of the Valeo V4X ECU installed on Renault Duster cars and for reading/writing calibrations and programs of the Sagem S3000 ECU (512k FLASH) installed on Renault cars via the diagnostic connector. Additional functions: Calculation of checksum for calibration area ECU identification: allows requesting ECU identification data An J2534 adapter is required for operation. To use the module, you need to purchase a Loader Package v.3. The loader package can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you will need: serial number of the key, USB host, full name, and email address. Activation is performed during business hours within 5-10 minutes, with delays up to 1-2 hours on weekends.
In Stock
Combiloader Ford EMS2204/EMS2211 [032] module set

$63

Combiloader Ford EMS2204/EMS2211 module set is designed for reading/writing software and/or calibrations of Ford Siemens EMS2204/EMS2211 ECUs installed on Ford Focus III cars with 1.6L engines. Adapter J2534 is required for operation. To use the module, you need to purchase the Loader Package v.3. You can buy the loader package in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Continental EMS3110/3120/3125/3150 [033] module set

$63

Combiloader EMS 3110/3120/3125/3150 module set is designed for reading/writing calibrations and programs of Continental EMS3110, EMS3120, EMS3125, and EMS3150 ECUs installed on Renault and Lada vehicles through the diagnostic connector. Additional Functions: Calculation of calibration checksum ECU Identification: allows requesting ECU identification data To work with EMS3120/EMS3125/EMS3150 ECUs, which include full access to FLASH/EEPROM, the module's capabilities can be expanded by purchasing an additional license called Renault Extra. To use the module, it is necessary to purchase the PAK Loader v.3. The loader can be purchased in our store. An unlimited number of modules can be installed on one loader. To activate the module, you will need the serial number of the key, USB host, your full name, and email address. Activation is performed during working hours within 5-10 minutes, and on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader Cummins CMx [035] module

$188

Combiloader Cummins CMx Module is designed for reading/writing FLASH memory of Cummins CM876/2150/2220/2880/2350/2670C/2670F ECUs, installed on vehicles of GAZ/MAZ/KAMAZ and others through the diagnostic connector. The module provides a flexible mechanism for reading/writing ECU configuration parameters. An J2534 adapter is required for operation. To use the module, it is necessary to purchase Loader Package v.3 Loader can be purchased in our store. An unlimited number of modules can be purchased with one loader. To activate the module, you will need: the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader Renault EMS3130 [036] module

$25

The Combiloader Renault EMS3130 module is designed for reading/writing calibrations and control unit programs EMS3130 installed on Renault Duster 1.6L cars through the diagnostic connector. Additional functions: Calculation of the calibration area checksum Change VIN: allows you to change the VIN code in the loaded firmware ECU Identification: allows you to request ECU identification data To use the module, you need to purchase Loader Package v.3 The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader VAG MagnetiMarelli 4HV/7GV [037] module

$63

Module Combiloader VAG MagnetiMarelli 4HV/7GV is designed for reading and writing FLASH ECUs of VAG group vehicles through the diagnostic connector. Supported ECUs: MagnetiMarelli MM4HV: petrol engines 1.4L BUD, BXW, CGGA, CGGB MagnetiMarelli MM7GV/GVE: petrol engines 1.4/1.6L CFNA, CFNB, CLRA, CLPA, CLPB, CLSA, CGGB The module automatically corrects the calibration checksum during writing. To use the module, you need to purchase a Loading Package v.3 You can buy the package in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you will need: key serial number, USB host, full name, and email address. Activation will be done within 5-10 minutes during business hours and may take up to 1-2 hours during weekends.
In Stock
Combiloader Delphi MT05 [038] module

$101

The Combiloader Delphi MT05 module is designed for reading/writing FLASH and EEPROM control blocks of Delphi MT05 and MT05.2 units installed on various motorcycle models. The Delphi MT05 and MT05.2 control units differ in the type of processor used and the size of the FLASH memory. The FLASH size for Delphi MT05 is 128KB, and for Delphi MT05.2 it is 256KB. The type of ECU is determined automatically by the module. The module allows you to: Read the full FLASH image and write software or calibrations Read and write the EEPROM region Perform automatic checksum calculation for the calibration region Retrieve software identification To use the module, you need to purchase the Loader Package v.3 The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you will need: the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, and on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader GM Siemens ACDelco [039] module

$38

Module Combiloader GM Siemens ACDelco is designed for reading/writing FLASH memory of Siemens ACDelco ECUs 5WY7128 installed in GM Cadillac STS/SRX vehicles through the diagnostic connector. The module calculates the checksum of the calibration area. To use the module, it is necessary to purchase Loader Package v.3. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, the following information is required: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, and on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader PSA Bosch ME7.4.4/5, Valeo V46/J34P [040] module set

$63

Module Set Combiloader PSA Bosch ME7.4.4/5, Valeo V46/J34P is designed for reading/writing FLASH memory of ECU Bosch ME7.4.4, Bosch ME7.4.5, Valeo V46, and Valeo J34P, installed on Citroen/Peugeot (PSA) cars through the diagnostic connector. Additional features: ECU Identification: allows requesting ECU identification data Error Reading: reads the number of DTCs from the ECU and displays their codes Initialization: allows performing ECU initialization after reprogramming Automatic calculation and correction of the calibration areas checksum An adapter J2534 is required for operation. The module requires the purchase of a Loader Pack v.3 The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you will need: serial number of the key, USB host, full name, and email address. Activation will be performed during business hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader Delphi MT34, MT80 China, MT92 GW [041] module set

$101

Combiloader Delphi MT34/MT80 China, MT92 GW Module Kit is designed for flashing the ECU (Engine Control Unit) Delphi MT34/MT80 China, MT92 GreatWall installed in GreatWall/Haval/Geely cars through the diagnostic connector. An J2534 adapter is required for operation. To use the module, you need to purchase the Loader Package v.3 The loader can be purchased in our store. One loader can be used for an unlimited number of modules. To activate the module, you need: the serial number of the key, USB host, full name and email address. Activation is carried out during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader M86/M74M (VAZ) [042] module

$63

Combiloader M86/M74M Module (VAZ Software) The Combiloader M86/M74M module is designed for reading/writing FLASH and EEPROM of ECU M86/M74M with VAZ software, based on Infineon processor family XC27x5, through the built-in BootStrapLoader, as well as software writing through the diagnostic connector. The control unit can be operated without disassembling. Software can also be written to the vehicle through the diagnostic connector, requiring a J2534 adapter for operation. The functionality of the module does NOT INTERSECT with the Mikas-12/M75/M74.5/M75/M86i module (Itelma Software). Both modules are required to work with the entire M86 lineup. To use the module, it is necessary to purchase the Loader Package v.3 You can purchase the loader package in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you need the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Transtron Isuzu [045] module set

$101

The Combiloader Transtron Isuzu module set is designed for reading/writing the FLASH memory of the Transtron ECU via the CAN bus. It is compatible with Isuzu vehicles equipped with Renesas processors and engines 4JJ1, 4JK1, 4HK1, 6HK1 through the diagnostic connector. The set includes the following modules: Transtron Isuzu 7058 J2534, designed for reading/writing the FLASH memory of Transtron ECUs based on Renesas SH7058 processors with bootloader in the ECU software. Transtron Isuzu 705x R/O J2534, designed for reading the FLASH memory of Transtron ECUs based on Renesas SH7055/7058 processors. An J2534 adapter is required for operation. To use the module, the purchase of Loader Set v.3 is required. The loader set can be purchased at our store. You can purchase an unlimited number of modules for one loader. To activate the module, you will need the serial number of the key, USB host, full name and email address. Activation is done during working hours and takes 5-10 minutes, or with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Renault SID301/305/306/307, EDC17C11/C42, DCM3.4 [046] module set

$101

The Combiloader module kit for Renault SID301/305/306/307, EDC17C11/C42, DCM3.4 is designed for reading/writing software and/or calibration areas of ECUs installed in Renault/Nissan vehicles with diesel engines through the diagnostic connector. The kit includes the following modules: SID301 Renault (J2534) for reading and writing FLASH memory of SID301 ECUs SID305/306 Renault (J2534) for reading and writing FLASH memory of SID305/SID306 ECUs Continental SID307 for reading/writing calibrations and ECU program of Continental SID307 Bosch EDC17C11 Renault (J2534) for reading and writing FLASH memory of Bosch EDC17C11 ECUs Bosch EDC17C42 Renault (J2534) for reading and writing FLASH memory of Bosch EDC17C42 ECUs Delphi DCM3.4 Renault (J2534) for reading and writing FLASH memory of Delphi DCM3.4 ECUs To work with SID307 ECUs, which provide full access to FLASH/EEPROM, you can extend the module's capabilities by purchasing an additional license Renault Extra. An adapter J2534 is required for operation. To use the module, you need to purchase the Programming Package v.3 You can purchase the programming package in our store, and one package allows you to buy an unlimited number of modules. To activate the module, you will need the serial number of your key, USB host, your full name, and email address. Activation is carried out during working hours and usually takes 5-10 minutes, with possible delays of 1-2 hours on weekends.
In Stock
Combiloader Siemens SIMK2K-243 GM [047] module

$63

Module Combiloader Siemens SIMK2K-243 GM is designed for reading/writing calibrations and ECU program Siemens SIM2K-243 GM installed on Chevrolet Spark M300 cars. The module allows you to work without removing the ECU from the car through the J2534 interface. To work with the module, you need to purchase Loader Package v.3. The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader Bosch EDC7UC31 [048] module

$63

Combiloader Bosch EDC7UC31 module is designed for reading/writing the FLASH memory of Bosch EDC7UC31 control units installed on KAMAZ/MMZ/MTZ/YAMZ/BAW/Dayun/DongFeng/FAW/Shaanxi. To use the module, the purchase of Combiloader v.3 is required. You can purchase the loader in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you need the following information: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes and may be delayed up to 1-2 hours on weekends.
In Stock
Combiloader AMT (VAZ) [049] module

$62

Combiloader AMT module (VAZ) is designed for reading/writing the FLASH memory of the AMT ECU installed on VAZ cars via the diagnostic connector. The module automatically corrects the checksum of the calibrations during writing. An J2534 adapter is required for operation. To work with the module, you need to purchase Loader Package v.3. The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader Renault UDS [050] module set

$126

Combiloader Renault UDS module set is designed for reading/writing calibrations and ECU programming of Continental/Bosch installed in Renault/Nissan vehicles through the diagnostic connector. The set includes the following modules: Continental SID309 for reading/writing calibrations and programming, installed on 1.5L engines Continental SID310 for reading/writing calibrations and programming, installed on 1.5L and 2.3L engines Continental EMS3155 for reading/writing calibrations and programming, installed on 1.2T engines Bosch EDC17C84 (J2435) for reading/writing calibrations and programming, installed on 1.6L engines Additional functions: Calculation of calibration area checksum ECU identification: allows requesting ECU identification data To work with EMS3155/SID309/SID310 ECUs, providing full access to FLASH/EEPROM, module capabilities can be expanded by purchasing an additional license for Renault Extra. To work with the module, the purchase of Loader Package v.3 is required. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you will need: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with delays up to 1-2 hours on weekends.
In Stock
Combiloader PSA SID208 [051] module

$126

Module Combiloader PSA SID208 is designed for reading/writing FLASH and EEPROM of the control unit SID208 installed on Peugeot Boxer/Citroen Jumper cars through the diagnostic connector and on a removed ECU. Additional functions: Calculation of calibration area checksum ECU identification: allows to request ECU identification data Reading ECU password: allows to read ECU password for BSL TC17xx J2534 module operation Reading and clearing errors To use the module, you need to purchase Loader Package v.3 The loader can be purchased in our store. One loader can be used with unlimited number of modules. To activate the module, you will need: serial number of the key, USB host, full name, and email address. Activation is carried out during working hours within 5-10 minutes, with delays up to 1-2 hours on weekends.
In Stock
Combiloader PSA Delphi DCM6.2 [052] module

$88

Chapter Combiloader PSA Delphi DCM6.2 is designed for reading/writing calibrations and Delphi DCM6.2/6.2A/6.2C ECU programs installed on Peugeot/Citroen vehicles through the diagnostic connector. Additional features: Calibration checksum calculation ECU identification: allows requesting ECU identification data Error reading and clearing To use the module, it is necessary to purchase a Loader Package v.3 You can buy the loader in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Delphi MT22.3/22.5/62.1 [053] module

$63

The Combiloader Delphi MT22.3/22.5/62.1 module is designed for reading/writing FLASH memory of Delphi MT22.3/22.5/62.1 control units via the CAN bus through the diagnostic connector. Delphi MT22.5 ECUs have two different hardware modifications (externally identical): Programmable via CAN: this module supports working with such ECUs. Programmable via K-Line: this module does not support working with such ECUs, the module MT-20U should be used. Additional functions: Calculation of checksum for calibration area. Identification of the ECU. Reading and clearing ECU errors. To work with the module, it is necessary to purchase the Loader Package v.3 The loader can be purchased in our store. An unlimited number of modules can be acquired for one loader. To activate the module, you will need: key serial number, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of 1-2 hours on weekends.
In Stock
Renault Extra [054] extension set

$88

The Renault Extra expansion kit provides full access to the FLASH/EEPROM of Continental ECUs, including SID301/SID307/SID309/SID310 and Continental EMS3120/EMS3125/EMS3150/EMS3155, with the ability to clone blocks on the workbench without IMMO response. The expansion kit does not work without the main module Renault SID301/305/306/307, EDC17C11/C42, DCM3.4 [046]. To use the module, you need to purchase the Programming Package v.3 You can purchase the programming package in our store, and one package allows you to buy an unlimited number of modules. To activate the module, you will need the serial number of your key, USB host, your full name, and email address. Activation is carried out during working hours and usually takes 5-10 minutes, with possible delays of 1-2 hours on weekends.
In Stock
Delphi MT80, MT60 [055] extension set for modules

$88

Extensions Extensions for Delphi MT60/MT80 modules are available through an additional license (GM Extra), which includes full access to FLASH/EEPROM, the boot block, and the VID block without the need for disassembly or "cloning" of blocks. The extension set does not work without the main module Combiloader Delphi MT80, MT60, Simtec76 [009]. The extended functions are only available for Delphi MT60 and Delphi MT80. Working with the ECU's FLASH memory is done by holding down the modifier keys while pressing the Read or Write buttons on the FLASH tab. The keys can be released after the operation has started. To use the module, you must purchase the Loader Pack v.3 To activate the module, you will need the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader M73/М74K/Janvier 7.2+ (VAZ) [056]

$32

Module Combiloader M73/M74K/Janvier 7.2+ is designed to work with control units Janvier-7.2+/M73/M74K, installed on VAZ vehicles. Does not work with "closed" versions of ECU M73! ECU programming must be done by connecting to the ECU connector. Programming without removing it from the vehicle by connecting to the diagnostic connector can cause damage to fuses, actuators, or components inside the ECU. To use the module, you need to purchase Loader Set v.3 The loader can be purchased at our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader М10.3 [058] module

$38

The Combiloader M10.3 module is designed for reading/writing FLASH and EEPROM content of the control blocks of Micas-10.3/11 (M103/M113) installed in Daewoo, Ukrainian assembly ZAZ, and GAZ cars. To work with the module, the purchase of Loader Pack v.3 is required. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you will need the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Daewoo GM IEFI‑6/ITMS-6F [059] module

$101

Combiloader Daewoo GM IEFI-6/ITMS-6F module is designed for reading/writing FLASH ECM GM IEFI-6/ITMS-6F installed in Daewoo cars. ECM programming is performed directly on the vehicle through the OBDII diagnostic connector, and the Combiloader OBD2 cable is used t"box-sizing: inherit; outline: none; line-height: 1.214; margin-right: 0px; margin-bottom: 2.4rem; margin-left: 0px;">To use the module, you need to purchase the Loader Kit v.3 The loader kit can be purchased in our store. You can purchase an unlimited number of modules with one loader kit. To activate the module, you will need the following: serial number of the key, USB host, full name, and email address. Activation is performed within 5-10 minutes during business hours and may be delayed up to 1-2 hours on weekends.
In Stock
Combiloader Siemens Sirius D3x/D4x [060] module

$88

Module Combiloader Siemens Sirius D3x/D4x is designed for reading/writing the content of Siemens Sirius D3x/D4x FLASH ECUs installed in Chevrolet and Daewoo cars. ECU programming can be performed directly on the vehicle by connecting to the diagnostic connector through an additional cable. Supported cars: Chevrolet: Lacetti, Aveo, Tacuma, Rezzo Daewoo: Matiz To use the module, the purchase of a Loader Kit v.3 is required. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you will need: the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader BMW Siemens MS41/42/43 [061] module

$62

Module Combiloader BMW Siemens MS41/42/43 is designed for reading/writing calibrations of Siemens MS41/42/43 ECUs installed in BMW cars. Programming of Siemens MS41/42/43 ECUs on BMW cars E36/E38/E39/E46/E53 2.0/3.0L can be done directly on the car through the diagnostic connector. To work with the module, it is necessary to purchase Loader Package v.3. The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of 1-2 hours on weekends.
In Stock
Combiloader DSI TCM/EAST80 [062] module

$88

Module Combiloader DSI TCM/EAST80 is designed for flashing software/calibrations of Continental DCT ECUs, Continental EAST80.D1 ECUs installed in GreatWall/Haval vehicles, and Continental EAST80.F1 ECUs installed in Hawtai vehicles. Module kit includes: DSI TCM for reading/writing FLASH memory of DSI TCM ECUs installed in SsangYong/Geely vehicles via diagnostic connector Continental EAST80.D1 for reading/writing software/calibrations of Continental EAST80.D1 ECUs installed in GreatWall/Haval vehicles Continental EAST80.F1 for reading/writing software/calibrations of Continental EAST80.F1 ECUs installed in Hawtai vehicles The module automatically corrects calibration checksums during the flashing process. J2534 adapter is required for operation. Module operation requires the purchase of Loader Package v.3. The loader package can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with delays up to 1-2 hours on weekends.
In Stock
Module 063. ABIT M20.20/M20.21/M240/MD22 (Combiloader)

$125

Abit M20.20.M20.21/M240/MD22 Module Kit Attention! This module is compatible with CombiLoader 2.16 or later versions. Designed for working with Abit M20.20, M20.21, M240, M240S1, MD22 engine control units (ECUs) for chip tuning and diagnostics. Features: Read and write calibration data; Read and write control programs; Calculate and automatically correct the checksum of the calibration area; ECU identification; Read and reset diagnostic trouble codes (DTCs). To work with the module, you need to purchase Loader Package v.3. The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader BSL Tricore TC17xx [064 – 067] module

$63

Module Combiloader BSL Tricore TC17xx is designed for reading/writing FLASH and EEPROM of Tricore TC17xx ECUs based on Infineon processors through the built-in BootStrapLoader. Which ECUs are supported by this module: ME17.9.7, VAZ, UAZ M(E)17.9.71, TPROT 12, UAZ ME17.9.11/12, Hyundai, Kia Continental SID-208 Continental SIM2K-C201, SIM2K-24x Continental EMS2204 Delphi MT80 Various ECUs of the MED17 family Various ECUs of the EDC17 family Other types of ECUs with TriCore processors BSL TC17xx module is available in three versions: Version 1: BSL Tricore TC17xx Limited (VAZ/UAZ) Flash/Eeprom writing is only available for VAZ/UAZ vehicles Reading ECU password is possible, checksum correction is NOT AVAILABLE Saving the read firmware is only possible in BCF format Version 2: BSL Tricore TC17xx Full Flash/Eeprom writing is available without restriction Reading ECU password is possible, checksum correction is NOT AVAILABLE Saving the read firmware is only possible in BCF format Version 3: BSL Tricore TC17xx Full CS Flash/Eeprom writing is available for all compatible processors without restriction Reading ECU password is possible, automatic checksum correction is performed during writing Saving the read firmware is possible in BCF and BIN formats Users of versions 2 and 3 can use the Bosch MEDC17 Hyundai/Kia module for free, which is designed for writing the FLASH memory of Bosch MEDC17 ECUs via the diagnostic connector. The module also includes the ability to read passwords for specific types of Bosch and Siemens/Continental ECUs. An J2534 adapter is required for operation. The module requires the purchase of Package Loader v.3. The Loader can be purchased from our store. An unlimited number of modules can be purchased for one Loader. To activate the module, you will need the serial number of the key, USB host, full name, and email address. Activation will be done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader HK/HK-UDS/China Bosch MEDC17 [065] module set

$101

Combiloader HK/HK-UDS/China Bosch MEDC17 module set is designed for chip tuning of Bosch ME17 China ECUs installed in GreatWall/Chery/Geely/Haval vehicles and Bosch MEDC17 ECUs installed in KKIA/Hyundai vehicles. The set includes the following modules: Bosch ME17 China (J2534) for reading calibrations and flashing software and/or calibrations of Bosch ME17, ME17.8.8, ME17.8.8.1, MED17.8.10, MED17.8.21, MED17.8.10.1, ME17U6 ECUs Bosch MEDC17 Hyundai/Kia UDS (J2534) for flashing the FLASH memory of Bosch MEDC17 Hyundai/Kia ECUs via UDS protocol through the diagnostic connector Bosch MEDC17 HK (J2534) for reading and flashing the FLASH memory of Bosch MEDC17 Hyundai/Kia ECUs through the diagnostic connector The Bosch MEDC17 Hyundai/Kia module supports the following ECU types: (read/write) Bosch EDC17C08 (read/write) Bosch EDC17CP14 (TPROT3) (read/write) Bosch EDC17CP14 (TPROT11) (read/write) Bosch EDC17C53 (read/write) Bosch MEx17.9.11/12/13 (read/write) Bosch MEx17.9.2 (read/write) Bosch MEx17.9.8 (read/write) Bosch MEx17.9.21 The Bosch MEDC17 Hyundai/Kia UDS module supports the following ECU type: (read/write) Bosch EDC17C57 (modified software in unlocked ECUs) It is a free application for all users of the BSL TC17xx J2534 module version 2 or 3. To use the module, you need to purchase the Loader Package v.3. The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: the serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of 1-2 hours on weekends.
In Stock
Combiloader Bosch ME17.9.7 OBD [068] module

$38

Module Combiloader Bosch ME17.9.7 OBD is designed for reading/writing the FLASH memory of the Bosch M(E)17.9.7/71 ECU installed on VAZ and UAZ vehicles using diagnostic method without disassembling the ECU. To use the module, it is necessary to purchase Loader Package v.3 . The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need the serial number of the key, a USB host, full name and email address. Activation is done during working hours within 5-10 minutes and on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader Bosch EDC17CV44/54 [069] module

$63

The Combiloader Bosch EDC17CV44/54 module is designed for reading/writing the FLASH memory of the Bosch EDC17CV44 and EDC17CV54 ECUs installed in MMZ/MTZ/YMZ/BAW/C&C/CAMS/FAW/FUSO/KINGKAN/SHAANXI/SITRAK/ASHOK LEYLAND trucks. The module automatically recalculates checksums. An J2534 adapter is required for operation. The module requires the purchase of the Loader Package v.3. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you will need: the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader PSA Bosch MEDC17 PSA and SID807 [070] module set

$63

The Combiloader PSA Bosch MEDC17 PSA and SID807 module set is designed for chip tuning of Bosch MEDC17 and SID807 ECUs in Peugeot/Citroen vehicles through the diagnostic connector. The modules perform automatic correction of calibration checksums during writing. Modules included in the set: Bosch MEDC17 PSA (J2534) for reading/writing ECU FLASH memory SID807 PSA (J2534) for writing ECU FLASH memory The modules support the following ECU types: Bosch EDC17C10 (TC1797 processor) Bosch MED17.4 (TC1766 processor) Bosch MED17.4 (TC1796 processor with external memory) Bosch MEV17.4 (TC1766 processor) Bosch MEV17.4 (TC1796 processor with external memory) Bosch MEV17.4.2 (TC1767 processor) SID807 (TC1796 processor with external memory) SID807EVO (TC1797 processor) Supported file formats: Uncompressed BIN (standard binary file) Compressed BIN (SMS-BIN format) SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader) To use the module, the purchase of Loader Package v.3 is required. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you will need: the serial number of the key, USB host, full name, and email address. Activation is done during business hours within 5-10 minutes, with delayed response up to 1-2 hours on weekends.
In Stock
Combiloader VAG Bosch MEDC17 UDS [071] module

$101

Module Combiloader VAG Bosch MEDC17 UDS is designed for flashing software and calibrations of Bosch MEDC17 ECUs of VAG vehicles through the diagnostic connector using UDS protocol. The module performs automatic correction of checksums during flashing. It supports the function of "Virtual Reading" of ECUs. The module supports the following types of ECUs: Bosch EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24, EDC17CP44, EDC17C46, EDC17C54, EDC17C64. Bosch MED17.1, MED17.1.1, MED17.1.6, MED17.5, MED17.5.5, MED17.5.20, MED17.5.21, MED17.5.22, MED17.5.24, MED17.5.25, MED17.5.26. Supported file formats: Uncompressed BIN (ordinary binary file) Compressed BIN (SMS-BIN format) SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader) To use the module, the purchase of Loader Package v.3 is required. The loader package can be purchased in our store. An unlimited number of modules can be purchased for one loader. Activation of the module requires: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with delays up to 1-2 hours on weekends.
In Stock
Module Combiloader BMW Exx Bosch MEDC17 [072]

$126

The Combiloader BMW Exx Bosch MEDC17 module is designed for flashing software and calibrations in the ECU Bosch MEDC17 of BMW Exx series cars via the diagnostic connector. The module automatically corrects checksums of calibrations during flashing and supports the "Virtual Reading" function of the ECU. The module supports the following types of ECUs: Bosch EDC17C06, EDC17C50, EDC17CP02, EDC17C41, EDC17CP09, EDC17CP45 Bosch ME17.2.1/ME17.4.5, MEV17.2.1/ME17.4.6, MEVD17.2, MEVD17.2.2 Supported file formats: Uncompressed BIN (standard binary file) Compressed BIN (SMS-BIN format) SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader) To use the module, you need to purchase the Programming Package v.3. The programming package is available for purchase in our store, and you can use it to activate an unlimited number of modules. To activate the module, you will need the serial number of the key, USB host, your full name, and email address. Activation is carried out during working hours and usually takes 5-10 minutes, with possible delays of 1-2 hours on weekends.
In Stock
Module Combiloader VAG Bosch MEDC17 K/CANTP2.0 [074]

$101

The Combiloader VAG Bosch MEDC17 K/CANTP2.0 module is designed for flashing software and calibrations of Bosch MEDC17 ECUs in VAG group vehicles via K-line or CANTP2.0 protocol through the diagnostic connector. The module performs automatic checksum correction of calibrations during flashing and supports the "Virtual Reading" function of the ECU. The module supports the following types of ECUs: Bosch EDC17U01, EDC17U05, EDC17CP04, EDC17CP14, EDC17CP20, EDC17CP24 Bosch MED17.1, MED17.1.1, MED17.5, MED17.5.1, MED17.5.2, MED17.5.5, MED17.5.6, ME17.5.20 Supported file formats: Uncompressed BIN (standard binary file) Compressed BIN (SMS-BIN format) SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader) To use the module, the purchase of Loader Package v.3 is required. The loader can be purchased in our store. An unlimited amount of modules can be installed onto one loader. Activation requires: key serial number, USB host, full name and email address. Activation if performed during working hours in 5-10 minutes, with a delay on weekends up to 1-2 hours.
In Stock
Combiloader WestPort WP580 [075] module

$126

The Combiloader WestPort WP580 module is designed for reading/writing the FLASH memory of the WestPort WP580 ECU installed in GAZ and other vehicles via the diagnostic connector. An adapter J2534 is required for operation. To use the module, you need to purchase the Loader Kit v.3. The loader can be purchased in our store. You can buy an unlimited number of modules for one loader. To activate the module, you will need the serial number of the key, USB host, full name, and email address. Activation takes place during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Module Combiloader Suzuki Bosch MEDC17 [076]

$63

The Combiloader Suzuki Bosch MEDC17 module is designed for reading/writing software and calibrations for Bosch MEDC17 ECUs in Suzuki cars through the diagnostic connector. The module automatically corrects the checksum of calibrations during writing. The following types of ECUs are supported by the module: Bosch ME17.9.5 Bosch ME17.9.51 Bosch ME17.9.6 Bosch ME17.9.61 (writing after disabling the security protection) Supported file formats: Uncompressed BIN (standard binary file) Compressed BIN (SMS-BIN format) SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader) To use the module, the purchase of Loader Pack v.3 is required. The loader pack can be purchased in our store. An unlimited number of modules can be purchased for one loader pack. To activate the module, you will need: the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Bosch MEDC17 BSM [079] module

$190

The Combiloader Bosch MEDC17 BSM module is designed for reading/writing on the table, without opening the block, FLASH/EEPROM ECU Bosch MEDC17 series using the BSM (Bosch Service Mode) protocol. The module automatically corrects calibration checksums during writing. The module does not support work with ECUs with TPROT above 3 for TC1766/TC1796 and ECUs with Chinese software. Supported file formats: Uncompressed BIN (regular binary file) Compressed BIN (SMS-BIN format) SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader) To use the module, connection to the ECU is required using the J2534 adapter DiaLink or SM2 Pro. To use the module, the purchase of Loader Package v.3 Loader can bo bought in our shop. An unlimited amount of modules can be installed onto one loader. Activation requires: key serial number, USB host, full name and email address. Activation if performed during working hours in 5-10 minutes, with a delay on weekends up to 1-2 hours.
In Stock
Combiloader HK SIM2K-25x, SIM2K-26x [080] module set

$126

The Combiloader HK SIM2K-25x, SIM2K-26x module kit is designed for reading/writing Siemens SIM2K-250, SIM2K-251, SIM2K-253, SIM2K-259, SIM2K-260, SIM2K-261 ECUs installed in Hyundai and Kia vehicles. The work is done by opening the ECU, without opening the ECU (after preparation), or in diagnostic mode, functions such as identification, error reading/reset, and firmware and/or calibration writing are available. Additional features: The module automatically recalculates the checksums of the written calibrations. The module allows for full reading and writing of the ECU's content. The module allows for disabling the ECU's digital signature check. To use the module, you need to purchase the Bootloader Package v.3. The bootloader can be purchased in our store. An unlimited number of modules can be purchased for one bootloader. To activate the module, you need the following: key serial number, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Bosch EDC16 BSM and Bosch ME9 BSM [081] module set

$190

Combiloader Bosch EDC16 BSM and Bosch ME9 BSM module kit is designed for reading/writing FLASH/EEPROM of Bosch ECU series EDC7/EDC16/PSG16/ME9 without opening them using BSM (Bosch Service Mode) protocol. This module does not support working with ME9 ECUs from the following manufacturers: BMW, MercedesBenz. Supported file formats: Uncompressed BIN (regular binary file) SMS-Soft Container File (new format for ChipTuningPRO and CombiLoader) To use the module, connection to the ECU is necessary using J2534 adapter DiaLink or SM2 Pro. To use the module, the Load Kit v.3 needs to be purchased. The Loader Kit can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, the following are required: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of 1-2 hours on weekends.
In Stock
Combiloader Abit A12.2 [082] module

$62

The Combiloader Module Abit A12.2 is designed for updating the controller program and reading/writing calibrations of ECU Abit A12.2 installed in GAZ cars. The module allows: To read/write the calibration area To read/write the control program To calculate and, if necessary, automatically adjust the checksum of the calibration area To perform ECU identification To use the module, you need to purchase the Combiloader Kit v.3. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you will need the serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Renault DC4 TCM/TA2005 TCM [083] module set

$63

Module Combiloader Renault DC4 TCM/TA2005 TCM is designed for reading/writing calibrations and ECU program of DC4/TA2005 TCM installed on Renault vehicles via diagnostic connector. Additional functions: Calculation of calibration area checksum ECU identification Writing VIN code of ECU (TA2005) To use the module, it is necessary to purchase Loader package v.3. You can purchase the loader in our store. You can buy an unlimited number of modules for one loader. To activate the module, you need: the serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader VAG Simos12/16/18 [085] module

$190

The modules are designed for reading and writing SIMOS 12.1/12.2/16.11/18.1/18.2/18.6/18.10 ECUs installed on VAG vehicles. Work with the SIMOS12.1/12.2 ECU is carried out on the table without opening the ECU. Virtual reading and writing of software/calibrations via the diagnostic connector is supported. Work with the SIMOS16.11 ECU is carried out on a table with the ECU opened. Virtual reading and writing of software/calibrations via the diagnostic connector is supported. Work with the SIMOS18.1/18.2/18.6/18.10 ECU is carried out on a table with the ECU opened. Supports virtual reading and writing of software/calibrations via the diagnostic connector (except SIMOS18.10). Identification and error reading/resetting functions are also available. The module automatically recalculates the CS of recorded calibrations. The module allows you to fully read and write the contents of the ECU with the exception of the OTP area. For the module to operate, it must be connected to the ECU using the J2534 DiaLink or SM2/SM2Pro adapter. Details in the documentation. To work with the module, you need to purchase Loader Package v.3. The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Ford Extra [086] extension set

$63

Set of Ford Extra Expansion Capabilities provides full access to FLASH/EEPROM ECU SID208/SID209(CK4A) through the diagnostic connector. The expansion kit does not work without the main module Ford SID206/208/209/211 [028]. To use the module, you need to purchase Package Loader v.3. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you will need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of 1-2 hours on weekends.
In Stock
Combiloader SIM271DE 2.0 MercedesBenz [087] module

$126

Combiloader SIM271DE 2.0 Mercedes-Benz module is designed for reading/writing SIM271DE 2.0/SIM271KE 2.0 ECUs installed in Mercedes vehicles. Working with the control unit can be done either through the vehicle's diagnostic connector or on the workbench without opening the ECU. Additional features: Available identification and error reading/reset functions Performs automatic recalculation of calibration checksums Allows for full reading and writing of ECU content To use the module, the purchase of Loader Package v.3 is required. The loader can be purchased in our store. An unlimited number of modules can be purchased per one loader. To activate the module, the following are needed: serial number of the key, USB host, full name, and email address. Activation is performed during business hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Ford EMS210x [089] module

$63

Module Combiloader Ford EMS210x is designed for reading/writing software and/or calibration areas of EMS2101(Test)/2102(Test)/2103 control units installed in Ford Fiesta, Mondeo 4 vehicles with 1.25L, 1.4L, 1.6L engines. Requires J2534 adapter to work. To use the module, you need to purchase Combiloader v.3 kit. The loader can be purchased in our store. You can buy an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of 1-2 hours on weekends.
In Stock
Combiloader SDIx Porsche [090] module

$63

Module Combiloader SDIx Porsch is designed for reading/writing SDI4/6/7/8 ECUs installed in Porsche cars. Working with control units can be done either through the car's diagnostic connector or on a table without opening the ECU. The module does not support working with SDI7 ECUs with hardware number 97061860202 (3.6L). Additional functions: Identification and error reading/reset functions are available Automatically recalculates checksums of written calibrations All ECU content can be fully read and written To use the module, you need to purchase a Loader Pack v.3. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader BMW MSVD8x/90 [091] module

$187

Module Combiloader BMW MSVD8x/90 is designed for reading/writing ECUs MSD80/MSD80.2/MSD81/MSD81.2/MSD85.0/MSD85.1/MSD85.2/MSD85.3/MSD87.2/MSV80.0/MSV80.1/MSV90 installed in BMW cars. Control unit operations are performed on the table without opening the ECU. Additional functions: Identification and error reading/reset functions are available for E-series ECUs Automatically recalculates checksums of written calibrations Allows full reading and writing of ECU contents To use the module, you need to purchase Loader Package v.3. The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Renault EMS3180 [093] module

$63

Module Combiloader Renault EMS3180 is designed for reading/writing calibrations and EMS3180 ECU program installed on Renault vehicles through the diagnostic connector. Additional functions: Calculation of the checksum area of calibrations ECU identification: allows requesting ECU identification data To work with EMS3180 ECU, which includes full access to FLASH/EEPROM, an extension of module capabilities is available for purchase as an additional license. To use the module, it is necessary to purchase Loader Package v.3 The loader can be purchased in our store. An unlimited number of modules can be purchased for one loader. To activate the module, you need: the serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader M74.8/M74.9 (J2534) [094] module

$114

Module Combiloader M74.8/M74.9 (J2534) is designed for reading/writing FLASH and EEPROM of new "anti-crisis" ECUs M74.8/M74.9 (ITELMA software) installed on Niva Legend and Travel cars (2022+). Working with control units is done without disassembling them. Modules included: Module for reading/writing FLASH and EEPROM of ECU M74.8 with ITELMA software, based on STMicroelectronics SPC58VQ series processors (Power architecture), as well as virtual reading software Module for reading/writing FLASH and EEPROM of ECU M74.9 with ITELMA software, based on Artery AT32F4xx series processors (ARM architecture), as well as virtual reading software J2534 adapter is required for operation. To use the module, you need to purchase Loader Package v.3. The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Bosch VDO MSE6.0 [095] module

$101

Module Combiloader Bosch VDO MSE6.0 is designed for reading FLASH and writing software/calibrations of ECU Bosch MSE6.0, installed on various models of motorcycles. To use the module, you need to purchase Loader Package v.3. You can buy the loader in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader China Delphi DCM6.2, DCM7.1 [096] module

$88

Module Combiloader China Delphi is designed for reading/writing calibrations and programming of Delphi ECUs installed in GreatWall/JAC/SsangYong/DongFeng vehicles through the diagnostic connector. Delphi DCM6.2AP installed in GreatWall/JAC; Delphi DCM6.2AP installed in SsangYong; Delphi DCM7.1AP installed in GreatWall/DongFeng. Additional functions: Calculation of checksum for calibration area ECU identification: allows to request ECU identification data Reading and clearing of errors To use the module, you need to purchase Loader Package v.3 The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is done during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader SDI9/SDI10 Porsche [097] module set

$63

The modules are designed for reading and writing SDI9/SDI10 ECUs installed on Porsche vehicles. Work with the ECU is performed on a table with the ECU opened. Identification and error reading/reset functions are also available. The module automatically recalculates the KS of the recorded calibrations. The module allows for full reading and writing of the ECU contents. To use this module, you need to purchase the Programming Package v.3 The programming package can be purchased in our store, and one package allows you to buy an unlimited number of modules. To activate the module, you will need the serial key number, USB host, full name, and email address. Activation is carried out during working hours and usually takes 5-10 minutes, with possible delays of 1-2 hours on weekends.
In Stock
Combiloader VAG Delphi DCM6.2V [098] module

$126

Module Combiloader Delphi DCM6.2V VAG is designed for reading/writing calibrations and programming of Delphi DCM6.2V ECUs installed in VAG group cars via UDS protocol through the diagnostic connector. Additional features: The module automatically corrects the checksum of calibrations during writing The module supports the "Virtual Reading" function of the ECU ECU reading is performed when connected "on the table" without opening the ECU To use the module, you need to purchase Loader Package v.3 The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, with a delay of up to 1-2 hours on weekends.
In Stock
Combiloader Bosch MG1 China [099] module

$88

Combiloader module is designed for reading/writing software and/or calibrations of Bosch MG1UA008/MG1US008 ECUs installed on Chinese cars. Supported ECU: Read and write the software area and/or calibrations (subject to the possibility of reading the software area by the ECU itself) Calculate and, if necessary, automatically adjust the checksum of the calibration area Identify the ECU Read and reset fault codes Add read protection using diagnostic method An J2534 adapter is required for operation. To work with the module, you need to purchase Loader Package v.3. The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader AECS UAZ [100] module

$62

The Combiloader AECS UAZ module is designed for flashing the base software and for reading/writing calibrations of AECS ECUs installed in UAZ vehicles. The module automatically corrects the checksums of calibrations during the flashing process. To use this module, you need to purchase the Programming Package v.3. You can purchase the programming package in our store, and one package allows you to buy an unlimited number of modules. To activate the module, you will need the serial key number, USB host, full name, and email address. Activation is carried out during working hours and usually takes 5-10 minutes, with possible delays of 1-2 hours on weekends.
In Stock
Combiloader SID605/WISE13H/WISE15/MD1/EQ EDC17CV54 J2534 [101] module

$251

Combiloader module is designed for reading-writing software/calibrations of SID605/WISE13H/WISE15/MD1/EQ EDC17CV54 ECUs installed on MAZ vehicles and Chinese-made vehicles via a diagnostic connector. Supported ECU: SID605: write software/calibrations. WISE15: read-write software/calibrations. WISE15C: read-write software/calibrations/configuration. Bosch MD1CC878/WISE13(SPC58): read-write software/calibrations. Bosch MD1CE100(TC299): read-write calibrations. Bosch MD1CE101(TC375): read-write calibrations. Bosch MD1CE868(TC375): read-write calibrations. EQ EDC17 V6: read-write software/calibrations. EQ EDC17 V7: read-write software/calibrations. Weichai WISE13H: read-write software/calibrations. An J2534 adapter is required for operation. To work with the module, you need to purchase Loader Package v.3. The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.
In Stock
Combiloader BSL mode SPC5/MPC5xxx [103] module

$190

Combiloader BSL mode SPC5/MPC5xxx module is designed for reading-writing FLASH/EEPROM of ECUs based on ST/Motorola/FreeScale/NXP processors of the SPC5/MPC5xxx families via the built-in BAM (BootAssistModule). Such ECUs include, for example: Delphi ACDelco E78 Delphi ACDelco E83 Delphi DCM6.2 Delphi MT62.1 SID605/WISE15/WISE15C Other types of ECUs with processors of the SPC5/MPC5xxx families. The module supports the following processors: MPC5565 MPC5566 MPC5674F SPC563M54/60/64 SPC564A80 For operation, a J2534 adapter is required, purchased separately. An J2534 adapter is required for operation. To work with the module, you need to purchase Loader Package v.3. The loader can be purchased in our store. You can purchase an unlimited number of modules for one loader. To activate the module, you need: serial number of the key, USB host, full name, and email address. Activation is performed during working hours within 5-10 minutes, on weekends with a delay of up to 1-2 hours.

1

false

false

true

Remove

Change

tr

true