%20CAN-100x100.webp)
%20CAN-1000x1000.webp)
Hurry to buy Promotion ends left
-
Discounts for module payments:
- 2–3 modules — extra 5% discount (use coupon BIT25_15)
- 4+ modules — extra 10% discount (use coupon BIT25_20)
- Carlist BitBox
Software module for working with Toyota Denso Gen2 (newGen) CAN engine control units
Module for reading/virtual reading and writing through the diagnostic connector of new generation Toyota Denso newGen control units installed in Toyota Lexus petrol and diesel vehicles.
Supported vehicles and control units by Bitbox module for Toyota Denso Gen2 (newGen) CAN:
FIDs: 23, 27, 28
The module consists of two types of protocols:
TYPE 1 (FID: 23, 27)
Supports reading and writing FullFlash control units via P5-CAN-bus, installed in petrol vehicles with the following engines: 2.0 6ARFSE, 2.0T 8ARFTS, 1.2T 8NRFTS, 3.5 2GRFKS, 3.5 7GRFSE.
The module also includes the option to install the READ PROTECTION patch, which disables the block reading function and protects your firmware from piracy.
- Engine MCU D76F0199GD 1280Kb
- Engine MCU D76F0196F1 1536Kb
- Engine MCU D76F0219F1 2048Kb
- Transmission MCU D76F0199GD 1280Kb
- Transmission MCU D76F0196F1 1536Kb
Supported models:Lexus NX 200t AGZ1# |
Supported engines:2.0 6AR-FSE |
TYPE 2 (FID: 28)
Supports virtual reading and writing of FullFlash with checksum and CVN correction for control units installed in petrol and diesel vehicles: 2.8TD 1GDFTV, 2.4TD 2GDFTV, 4.0 1GRFE, 2.7 2TRFE, 2NRFE, 3ZRFAE, and more.
- Engine MCU D76F0199GD 1280Kb
- Engine MCU D76F0196F1 1536Kb
- Engine MCU D76F0219F1 2048Kb
Supported models:Toyota C-HR ZGX10L |
Supported engines:2.8TD 1GDFTV |
To use the module, the purchase of a Bitbox USB protection key is required. The key can be purchased in our store. You can buy an unlimited number of modules with one key.
Module activation is done within 1 hour on business days (usually 10-15 minutes). Activation may be delayed during weekends and holidays (up to 2 hours).
To activate the module, ONLY the serial number of the key and email are required.
To work through the OBD2 connector, a J2534 adapter is required (Scanmatik 2, OpenPort 2.0, Dialink, Mongoose, etc.). More information about J2534 here.
To connect the control unit on the bench, additional equipment from the following list is required:
Powerbox and Combibox for PCMflash are fully compatible with Bitbox.
An activated module or license cannot be returned.
If you have entered the wrong key or device number, the return is not valid. It is not possible to modify the license for another device.
After status update to "Waiting for activation", the data has already been sent to the developer for activation. The order cannot be canceled or corrected starting from this status update.
Pay attention to all information specified in the description of modules and scripts taken from the manufacturer. We are not responsible if the information is not correct or there are some differences from the reality. In the disputed situation, it is necessary to look for a solution to the issue to the manufacturer.
Our store is not responsible for the functionality of the software module. We cannot guarantee the declared functions since we are not the developer.
