Software module for working with the engine control unit of petrol vehicles Kia/Hyundai.
Module for reading and writing control units installed on petrol vehicles of Korean brands Kia/Hyundai through the diagnostic connector using the CAN-bus.
Which vehicles and control units are supported by the Bitbox Kia/Hyundai Petrol CAN module:
FIDs: 70, 72, 73, 74, 77, 88, 93, 104, 368
Kefico CPEGD2.20.1/CPGDSh4.26.1 (FID: 70)
Kefico CPEGD2.20.1 and CPGDSh4.26.1 control units are based on the Infineon Tricore TC1782 processor with internal flash memory of 2.5Mb.
Reading and writing of calibration area via CAN-bus with checksum correction is allowed. Recovery is possible from any state.
Supported vehicles:
Kia/Hyundai 1.0-1.6 MPI/DOHC
Bosch ME(G)17.9.1x (FID: 72)
Bosch ME(G)17.9.11/12/13 series control units are based on the Infineon Tricore TC1762 processor with internal flash memory of 1.46Mb.
Reading and writing of FullFlash via CAN-bus with checksum correction is allowed.
Supported vehicles:
Kia/Hyundai 1.0-1.6 MPI/DOHC
Bosch ME(G)17.9.21 (FID: 74)
Bosch ME(G)17.9.21 series control units are based on the Infineon Tricore TC1724 processor with internal flash memory of 1.5Mb.
Reading and writing of FullFlash via CAN-bus with checksum correction is allowed.
Bosch ME(D)(G)17.9.8 (FID: 73)
Bosch ME(D)(G)17.9.8 series control units are based on the Infineon Tricore TC1767 processor with internal flash memory of 2.0Mb.
Reading and writing of FullFlash via CAN-bus with checksum correction is allowed.
Siemens SIM2K-47 (FID: 88)
Siemens SIM2K-47 control unit is based on the C167 processor with external flash memory of 512Kb.
Reading and writing of FullFlash via CAN-bus with checksum correction is allowed.
Siemens SIM2K-24x (FID: 93)
Siemens SIM2K-240/241/242/245 control units are based on the Infineon Tricore TC1767 processor with internal flash memory of 2Mb.
Reading and writing of FullFlash via CAN-bus with checksum correction is allowed.
Siemens SIM2K-141/341 (FID: 104)
Siemens SIM2K-141/341 control units are based on the Motorola MPC561 processor with external flash memory of 2Mb.
Reading of FullFlash and writing of calibration area via CAN-bus with checksum correction is allowed.
Siemens SIM2K-141.1 (FID: 144)
Siemens SIM2K-141.1 control units are based on the Motorola MPC563 processor with external flash memory and a total capacity of 2.5Mb.
Virtual reading and writing via CAN-bus with checksum correction of calibration area is allowed.
Delphi MT86 (FID: 77)
Delphi MT86 control unit is based on the Tricore TC1766 processor with internal flash memory of 1.46Mb.
Reading and writing of calibration area via CAN-bus with checksum correction is allowed.
Kefico M(E)(G)7.9.8 (FID: 368)
Kefico M(E)(G)7.9.8 control unit is based on the ST10F275 processor with internal flash memory of 832Kb.
BSL reading / virtual reading and writing of calibration area via CAN-bus with checksum correction is allowed.
To use the module, you need to purchase a Bitbox USB dongle . You can purchase the dongle in our store. One dongle can be used to activate an unlimited number of modules.
Module activation is done within 1 hour on business days (usually 10-15 minutes). Activation may be delayed during weekends and holidays (up to 2 hours).
To activate the module, ONLY the serial number of the dongle and email are required.
To work through the OBD2 connector, a J2534 adapter is required (Scanmatik 2, OpenPort 2.0, Dialink, Mongoose, etc.). Learn more about J2534 here .
To connect the control unit on the bench, the purchase of additional equipment from the following list is required:
Powerbox and Combibox for PCMflash are fully compatible with Bitbox.
1. No Refunds or Modifications for Digital Licenses
Activated modules or licenses cannot be returned or refunded.
If an incorrect key or device number is entered by the customer, the purchase is not eligible for return.
Licenses cannot be modified, transferred, or reissued for another device under any circumstances.
2. Irreversible Order Processing
After the order status changes to “Waiting for activation”, the data has already been sent to the developer.
From this point onward, the order cannot be canceled, edited, corrected, or refunded.
3. Responsibility for Software Functionality
Our store is not responsible for the functionality, performance, or declared features of any software module.
We do not guarantee the listed functions because we are not the developer.
4. Accuracy of Product Information
Module and script descriptions are provided directly by the manufacturer.
IOBD.io is not responsible for any inaccuracies, missing details, or differences between the description and actual operation.
In disputed situations regarding functionality or listed features, the customer must contact the manufacturer.
5. Customer Responsibility for Installation
IOBD.io sells professional automotive diagnostic software and equipment.
Installation, setup, configuration, and compatibility checks must be performed by the customer.
We do not provide remote installation, programming, or setup services unless explicitly stated otherwise.
6. Required Technical Knowledge
These products are intended for users with basic technical knowledge in automotive diagnostics.
The customer is fully responsible for understanding the installation process and using the software and hardware correctly.
7. No Liability for Incorrect Usage
IOBD.IO is not responsible for issues caused by:
incorrect installation
unsupported or incompatible hardware
improper configuration
third-party interference